Sale!

Junctek JDS6600-60M 60 MHz DDS Signal Generator

$146.99

JDS6600-60M – stationary signal generator with 2.4-inch TFT display.

AUEUUKUS
Clear

Description

The JDS6600-60M is the senior model of the previously announced series of arbitrary waveform generators. This is a high-performance signal source, with a maximum sampling rate of 266 MBps and a DAC resolution of 14 bits, with a minimum level of harmonic distortion of the shape of the generated oscillations.

A special feature of the generator design is the presence of two completely independent output channels (CH1 and CH2) with the possibility of forming a high-frequency sinusoidal signal in the range up to 60 MHz.

The JDS6600-60M can be used to create both simple and complex signals, and has 60 user-defined waveforms in its arsenal.

  • Formation of up to 60 types of arbitrary waveforms with a frequency of up to 6 MHz
  • 2.4-inch colour LCD display displaying the output waveform for two channels simultaneously
  • High measurement accuracy
  • Sampling rate 266 Kbps
  • Vertical resolution of 14 bits
  • Waveform memory 2.048 Kb
  • Frequency resolution 0.01 MHz
  • Built-in frequency meter up to 100 MHz and pulse counter
  • Saving and using 100 groups of settings
  • Precise adjustment of the pulse duration in the range from 30 ns to 4000 s
  • Fine tuning of phase deviation between two channels
  • Borehole correction, amplitude and frequency modulation
  • USB-UART interface
  • Short circuit protection
Signal Generator Specifications
Number of Channels 2
Bandwidth Requirements 60 MHz
Sample Rate 266 MBIT / s
Frequency Range 0.01 MHz – 60 MHz
Wavelength 2048 bits
Vertical Resolution 14 bits
Wave Specifications
Signal Form Sinusoidal, Rectangular, Triangular, Pulse (duty cycle correction), Sawtooth, Noise, Partia Sine, CMOS, DC level, Half-wave, Full-Wave, Pos-Ladder, Neg-Ladder, Noise, Exponential Rise, Exponential Fall, Tone, Sinc Pulse, Lorentz Pulse and any other signals (60 forms, with 15 groups set by default)
Frequency Specifications
Sinusoidal Signal 0.01 MHz – 60 MHz
Rectangular Signal 0.01 MHz – 15 MHz
Sawtooth Signal 0.01 MHz – 15 MHz
Pulse Signal 0.01 MHz – 6 MHz
TTL / CMOS 0.01 MHz – 6 MHz
Custom Signal 0.01 MHz – 6 MHz
Signal Rise Time ≤ 15 ns
Pulse Duration Adjustment Range 30 ns – 4000s
Permission 0.01 MHz
Frequency Accuracy ± 20 ppm
Frequency Stability ±1 ppm / 3 hours
Specifications of a Sinusoidal Signal
Harmonic Distortion < 1 MHz: ≥ 45 dB
1 MHz – 20 MHz: ≥ 40 dB
Full Harmonic Distortion < 0.8% (20 Hz – 20 kHz)
Specifications of a Rectangular Signal
Blowout ≤ 5 %
Duty Cycle 0.1 – 99.9 %
Specifications of the Sawtooth Signal
Linearity > 98 % (0.01 Hz – 10 kHz)
Amplitude Specifications
Output Amplitude Range 2 mVpp – 20 Vpp
Frequency ≤ 10 MHz
Amplitude Resolution 1 mV
Amplitude Stability ± 0.5 % / 5 hours
Output Signal
Impedance 50 ohms ± 10 %
Protection All channels can operate for more than 60 seconds when the load is short-circuited
DC Offset Specifications
Output Signal Amplitude > 4 V
Offset Adjustment Range -9.99 V to 9.99 V
Offset Resolution 0.01 V
Phase Specifications
Range 0 – 359.99°
Permission 0.01°
TTL / CMOS Output
Low Level & < 0.3 V
High Level 1 – 10 V
Rise / Fall Time ≤ 20 ns
Frequency Meter Specifications
Range 1 Hz – 100 MHz
Measurement Accuracy Capture time: 0.01 – 10 seconds
Counter Specifications
Measuring Range 0 – 4294967295
Mode 2 kinds of pairing mode, DC and AC
Counting Mode Manual
Input Range 2 mVpp – 20 Vpp
Measuring the Width of the Pulse Duration 0.01 microseconds (resolution), 20 seconds (maximum measured time)
Period 0.01 microseconds (resolution), 20 seconds (maximum measured time)
Specifications of the Oscillating Frequency Generator
Channels CH1 or CH2
Scan Type Linear, logarithmic
Duration of the Frequency Change Period 0.1 – 999.9 s
Setting Range Randomly set between the start and end points
Swiping Modes Up, down, up-down
Pulse Burst Generator Specifications
Number of Pulses 1 – 1048575
Modes Manual Trig, CH2 Trig, Ext.Tring (AC), Ext.Tring (DC)
General Features
Display 2.4-inch color TFT display, 320 x 240 pixels
Menu Languages English
Interface USB, UART with TTL levels
Food DC 5 V ± 0.5 V
Operating Temperature 0 – 40 ℃
Humidity < 80%
Overall Dimensions 194 x 178 x 69 mm
Equipment JUNE JDS6600-60M signal generator – 1 pcs

AC power adapter – 1 pcs
USB cable – 1 pcs
BNC cable – 1 pcs
BNC crocodile cable – 1 pcs
User manual – 1 pcs
Software disk – 1 pcs

Additional information

Weight 0.9 kg

Reviews

There are no reviews yet.

Be the first to review “Junctek JDS6600-60M 60 MHz DDS Signal Generator”

Your email address will not be published. Required fields are marked *